Thrifty Swift Time

Success!!! The PVC pipe yarn swift is complete! My husband and I had a lot of fun building it, the build went quickly, and it didn’t cut into the pocketbook much. Shopping for materials probably took longer than assembling the swift and the total cost (including sales tax, excluding outrageous transportation cost) was $18.30. I did a digital photo shoot of most of the process and thought I’d post some photos and instructions here for other thrifty knitters to use as a guide.

WARNING! I’ve taken ideas from other do-it-yourself PVC swifters before me - so this not an original design by any means. I do not want to infringe on any copyrights or offend anyone – so just in case, I apologize in advance. Now on with the show.

The Stuff

(1) 10’ stick of ½” PVC pipe ($1.52)
(4) ¾” to ½” PVC reducing tees ($.53/ea.)
(12) ½” PVC end caps ($.29/ea.)
(2) ½” PVC crosses ($1.28/ea)
(1) 4” lazy Susan ball bearing assembly ($3.49)
(4) 11/64”x ¾” thumb bolts ($.45/ea.)
(8) #4 x ¼” steel washers ($.06/ea.)
(8) 5/8” nylon washers - not sure what the inside diameter is ($.15/ea.)
(8) #4 x ¾” metal screws - rounded top with Phillips head ($.06/ea.)
Small amount of contact cement (or you could use PVC glue)
Yard stick or measuring tape
Marker or pencil
Saw (we used a jigsaw – but I imagine you could use about any type of hand saw)
Electric drill and drill bits (we predrilled all holes using a bit one or two sizes smaller than the bolts and screws we were using)
Screw/bit measuring guide (to aid with the step mentioned above)
Phillips head screwdriver

The Steps

1. Measure and mark your pipe sections. You will have (12) sections, as follows:
   (4) 12” sections
   (4) 11” sections
   (4) 7 ½” sections



2. Cut your pipe sections and remove any burrs.



3. Predrill one hole in the center of one side of each tee. You will be inserting the thumb bolts into these holes – so use a bit that is at least one size smaller than the diameter of the bolt. This will give you a snug fit to aid in stability.



4. Insert the thumb bolts into the tees. Screw in just until you can see the bolt on the inside of the tee. You will be inserting these over the PVC arms and want them to slide on easily.



5. Assemble the base by inserting the (4) 11” pieces into one of the crosses. Use your glue on the pipe ends and inside of the tees to hold pieces in place.



6. Center the lazy-Susan over the PVC cross on the base assembly. Using a pencil or marker, mark the hole placements on the bottom plate of the Susan onto the PVC pipe.
   
   
7. Using a drill bit at least one size smaller than the metal screws – predrill the holes you marked for the lazy-Susan.



8. Place the metal washers on the metal screws.



9. Center a nylon washer between the hole on the lazy-Susan and the hole on the PVC pipe – screw the metal screw through the hole on top of the Susan and into the hole in the pipe. The nylon washer is sandwiched between the Susan and the pipe – eliminating the gap between the two.



10. Repeat steps 8 – 9 for the remaining three holes.



11. Assemble the bottom of the swift by inserting the (4) 12” pieces into the remaining cross. Glue the pieces to the cross but it is important not to glue your pipe ends on yet.



12. Place the swift bottom assembly on the ground or other flat surface.



13. Follow steps 6 – 10 to attach the base assembly to the swift bottom assembly.



14. Assemble the swift posts by inserting the 7 ½” pieces into the ½” opening on the PVC tees.



15. Slide the post assembly over the bottom assembly arms. If you have already glued the end caps to the arms on the bottom assembly, you will be kicking yourself about now.



16. Glue the end caps onto exposed pipe openings.



17. Adjust your posts to your desired skein size. Snug up each post by turning the thumb bolts. Remember – “lefty loosey” and “righty tighty.” Do not tighten thumb bolts to snug - the PVC can be easily stripped by overtightening.



18. Grab some yarn (or a thrifted sweater to frog) and take her for a spin!

So that’s it. I am really pleased with my swift. I thank my husband for his time and his patience with me. He even let me use his jigsaw! We argued a bit over different opinions when it came to the engineering aspects of the project – but all in all – we had a good time and were both proud of the end product.

I had disassembled the mohair sweater I wanted to frog last night and got it ready to unravel. So as soon as the swift was complete I got to test it out. One note about mohair – small protruding hairs tangle making the sweater unraveling process less than smooth! Oh, but how nice it is to skein-as-you-go in lieu of skeining from a big pile of yarn on the floor!

I did not have time to try the Kool-Aid over-dye. You know, I hope this mohair sweater I’ve been blabbing about is mohair (remember, handknit sweater – no tag) because if it isn’t a protein based fiber…..well I won’t think about that right now - remember, this is an experiment. So next weekend – I’ll try the dye. After the dying I’ll need to wind the yarn into balls and take some nice photos to post on here and Ravelry. Man, it sure would be nice to have a ballwinder and a collapsible PVC lightbox. Hey, honey………….

Aim High and Shoot Low

Okay - I haven't totally purged all I had anticipated but made pretty good progress. The kids went through their clothes and shoes and we freecycled all. I couldn't believe the pile of stuff accumulated - the kids clothes and shoes were so tiny looking - obviously it's been a while since we cleaned out closets! Sadly, the freecycling did not go as smooth as the first time and I learned a few good lessons on how to fine tune my posts and replies. Live and learn and do better the next time, eh? I still need to tackle the linen closet and bathroom - maybe if I have a sudden burst of energy today I will do that.

I may be side-tracked and lead astray by my latest yarn-brain project. You see, I am on a pretty tight budget and must try to refrain from costly yarn and fiber related purchases - I am weak and this is not always easy for me. Needless to say I dare not venture to the local yarn store very often (which is only a mile from my house) and when I do I try to head straight for the clearance bins. But I do lust after good fibers and all tools of the knitting trade. So being the thrify knitter that I am - I keep my eye out for froggable sweaters at the local thrift stores and am always on the prowl for knitting tools. Yesterday I found a handknit mohair sweater for $1.98 and want unravel it and try overdying the yarn using Kool-Aid.

It would be much easier to unravel and skein using a swift - if only I had one. Soooooooo........ I recruited my super-smart, patient, ingenious, and loving husband to help me build a pvc pipe swift!!! I'm so excited!!! So far we've spent about $17.00 on the parts and pieces and I don't think we will need anything else, but you never know. So with any luck, today I may be "a froggin' me some mohair." Why yes, I am an Ozarkian native - why do you ask? Anyway, off to build a swift. Happy knitting all.

The Urge to Purge

Maybe it is just the spring cleaning bug - but as of late I have been feeling the need to unload a lot the "stuff" my family has accumulated over the years. I've just got to unload! So this past weekend I went through my dresser and closet. Goodbye size 9 jeans I will never wear (and haven't in at least five years) - goodbye shoes I thought I just had to have. I put the clothes and some magazines on Freecyle and they were gone within an hour! I love Freecycle!

I even went through my yarn. Yes, the stash is a little skinnier now. I donated acrylics to Lana (aka knitandpray) for her good works with Newborns in Need and the local animal shelters - she rocks as a charity knitter! I have "donated" some yarn to my husband's flea market booth - maybe yarn will help buy food this month!

I must continue to lighten the load. The purging this week will relieve my house of access sheets, pillow cases, blankets, towels, kids clothes and shoes, arts and crafts stuff, books, and hopefully kitchen stuff. I will most definitely be freecycling most - if not all of this "stuff." I know Mike may want to try to sell some stuff at his upcoming yard sale or at the flea market, but I love the idea of passing on what you don't need to others - free of charge. I just want in all gone and if someone else can use it......yippee - we all win.

'Tis a Journey

This was one of those weekends that just didn’t turn out how I had planned – and I thank God for that. I am blessed with a wonderful family. I was able to slow down this weekend and appreciate that fact.

We went on a short day trip to Arkansas Sunday. Of course, the girls didn’t want to go (Aly was nursing a recently broken heart and Tab was crampy), Levi was game but concerned about eating and my husband was disappointed that he wasn’t driving. We went anyway. Mike relinquished the wheel, I told the girls they had no choice, and I fed Levi shortly after leaving the house.

The ride began quietly as the children sulked and listened to their MP3 players. However, a few miles into the trip Tab began talking, Aly started to smile, Mike tried to enjoy the scenery, and Levi was full and content. It rained most of the time we were in Eureka Springs, the yarn shop was closed and we only spotted a couple of art cars. But during the trip back, listening to the kids sing together in the back seat, I was reminded that sometimes the ride is better than the destination.

Though I didn’t get to attend the art car parade, visit the local yarn shop in Eureka Springs, plant flowers, or clean out the closet – I did get to see my oldest daughter grow even more and learn a life lesson in love/losing love, I saw Levi and Tab bond and laugh, I started a pretty groovy new knitting project with yarn I already had, I got see joy on my husband’s face after he planted the flowers of his choice, and I didn’t clean out the closet.